Regular maintenance and cleaning will ensure a long life for the heating and cooling system as well as save you a few bucks. Keeping the air conditioner well maintained will ensure that you do not just save on cash on energy but ensure it remains in good condition for long, saving yours from early replacements. The heating and cooling professionals advise on regular attention to the AC systems to ensure they are in good working condition for high efficiency. The right time to make use of these tips is just before the cold season. Below are some steps to make sure HVAC in Long Beach CA is in good condition always.
The first thing you should do is to clean the fin of your system. Using a strong garden hose stream, spray via the fins of your unit from the inside. This will help flush out any debris or dust. You should never clean the fins using a pressure washer since the pressure can destroy the fins. In case the fins are dirty, use the fin cleaning sprays that are commercially available. Ensure you read the instructions of the manufacturer before using these products.
The next thing is to ensure you clean any area surrounding the unit. When you are done with it, remember to replace its fun cage. Using a rake, you should be able to remove any debris or leaves found outside its condenser. If there are some plants around the area, you should trim them to less than 2 feet. This is done to ensure the clean flow of air on the units. It is also good to cover the upper side of the condenser so as to prevent any debris from getting inside.
Level the system. Over some time, the pad where the condenser sits on can start tipping while the soil settles under it. A condenser unit that is not leveled well will make the compressor fail. You should, therefore, check regularly if the condenser is at the right level and use rot-resistance shims to level it up.
Evaporator coil should also be cleaned. This can be found inside the furnace unit or the blower. This should be done by removing some bolts and screws or foil duct tapes. When inside, remember to remove the dust with the right soft brush. From here, you can spray the coils by using the right no-rinse coils cleaners. Here, you will notice some foam and later drop inside its drain pot. You should use soap, a little bleach, and hot water when cleaning its drain pan.
Clean the plugged evaporator exhaust. The evaporator coil is charged with the responsibility of blowing warm, humid air from the inner part of your home. Heat from the air is absorbed by the cold coil and cooled, and then the cool air is circulated into your house.
It is also necessary to ensure the filters are changed. This is mostly on the blower, and it is good to remember to do it two times a year. In case you are located in a dusty location, you should change them more than two times. Be careful when dealing with the filters since some can lead to freezing on its indoor coil.
Although the above points are meant to ensure your heating and cooling unit is at its top shape, they are better carried out by a technician. This is because; a small mistake can lead to failure of your unit. Instead of risking using the DIY approach, it is better to hire competent technicians.
The first thing you should do is to clean the fin of your system. Using a strong garden hose stream, spray via the fins of your unit from the inside. This will help flush out any debris or dust. You should never clean the fins using a pressure washer since the pressure can destroy the fins. In case the fins are dirty, use the fin cleaning sprays that are commercially available. Ensure you read the instructions of the manufacturer before using these products.
The next thing is to ensure you clean any area surrounding the unit. When you are done with it, remember to replace its fun cage. Using a rake, you should be able to remove any debris or leaves found outside its condenser. If there are some plants around the area, you should trim them to less than 2 feet. This is done to ensure the clean flow of air on the units. It is also good to cover the upper side of the condenser so as to prevent any debris from getting inside.
Level the system. Over some time, the pad where the condenser sits on can start tipping while the soil settles under it. A condenser unit that is not leveled well will make the compressor fail. You should, therefore, check regularly if the condenser is at the right level and use rot-resistance shims to level it up.
Evaporator coil should also be cleaned. This can be found inside the furnace unit or the blower. This should be done by removing some bolts and screws or foil duct tapes. When inside, remember to remove the dust with the right soft brush. From here, you can spray the coils by using the right no-rinse coils cleaners. Here, you will notice some foam and later drop inside its drain pot. You should use soap, a little bleach, and hot water when cleaning its drain pan.
Clean the plugged evaporator exhaust. The evaporator coil is charged with the responsibility of blowing warm, humid air from the inner part of your home. Heat from the air is absorbed by the cold coil and cooled, and then the cool air is circulated into your house.
It is also necessary to ensure the filters are changed. This is mostly on the blower, and it is good to remember to do it two times a year. In case you are located in a dusty location, you should change them more than two times. Be careful when dealing with the filters since some can lead to freezing on its indoor coil.
Although the above points are meant to ensure your heating and cooling unit is at its top shape, they are better carried out by a technician. This is because; a small mistake can lead to failure of your unit. Instead of risking using the DIY approach, it is better to hire competent technicians.
About the Author:
If you are looking for info about Newport Beach air conditioner installation, come to our web pages online here today. More details are available at http://completecomfort-hvac.com/long-Beach-ac-repair/ now.
No comments:
Post a Comment